What Are the Electrical Requirements for an Indoor Trampoline Park or Climbing Gym in Sydney?
What are the electrical requirements for an indoor trampoline park or climbing gym in Sydney? These venues almost always need a three phase supply to run large air handling units across a big open floor, dedicated safety lighting and power circuits for auto belay systems, and RCD protection on every final subcircuit because of the sheer number of people moving through the space. Most trampoline parks and climbing gyms are fitted out inside a converted warehouse or industrial unit, which is usually where the electrical surprises start, because the existing supply was sized for storage, not for hundreds of active people and a full mechanical services load.
⚡ Quick Answers: Trampoline Park and Climbing Gym Electrical Requirements
- Do I need three phase power? Almost certainly yes. Large rooftop or ducted air conditioning units, extraction fans and compressors for equipment maintenance all run more efficiently and reliably on three phase power than on a single phase supply pushed to its limit.
- How much switchboard capacity do I actually need? It depends on your combined HVAC, lighting, point of sale, kitchen or cafe, and auto belay or access control loads added together, not just the floor area, so a proper load calculation by a licensed electrician should come before you sign a lease.
- Does every socket outlet need its own safety switch? Non domestic premises need RCD protection for final subcircuits supplying socket outlets, lighting and hand held equipment, which in practice means several RCDs spread across the switchboard rather than one shared unit for the whole building.
- What building classification applies? Indoor recreation venues like trampoline parks and climbing gyms are typically treated as assembly buildings under the National Construction Code, the same broad category used for indoor sports centres and stadiums, though your certifier makes the final call based on your specific fit out.
- Why does a warehouse conversion so often need a switchboard upgrade? The original switchboard was almost always sized for a storage or light industrial use, not for mechanical ventilation, bright safety lighting and a few hundred active visitors, so the gap between old capacity and new demand usually shows up as soon as the design load is calculated.
1. Why trampoline parks and climbing gyms need three phase power
A single phase supply tops out at a point where running large motors and compressors becomes inefficient and puts uneven strain on one leg of the supply. Trampoline parks and climbing gyms typically run several big pieces of equipment at once, including rooftop air conditioning condensers, mechanical extraction fans pulling air across a warehouse sized floor, and compressors used to service foam pits or inflatable attractions.
Three phase power spreads that load evenly and gives you the headroom to add equipment later without re engineering the whole supply. If your venue is moving into an existing industrial unit, checking whether upgrading from single phase to three phase power is needed should happen before you commit to fit out drawings, not after the shopfitter arrives, and our guide to three phase power for a warehouse or industrial unit in Sydney covers the same groundwork for any large open floor tenancy.
2. Keeping a big open floor comfortable: HVAC and ventilation loads
A trampoline park or climbing gym floor can run to thousands of square metres under a high warehouse ceiling, and that volume of air is genuinely hard to heat, cool and keep moving. Ventilation also has to deal with a few hundred active, sweating people at once, which is a very different design load to the office or retail use the building may have been fitted out for previously.
HVAC equipment of this size draws heavily on your power supply, and it usually has to share switchboard capacity with lighting, kitchen or cafe equipment, and any auto belay or access control systems. Getting an accurate maximum demand calculation done early avoids the common trap of installing air conditioning that trips the main switch the first time the venue is genuinely busy.
3. Lighting circuits for safety, atmosphere and sport
Lighting in these venues does two jobs at once. It needs to be bright and even enough that staff can see every trampoline bay or climbing wall section clearly for supervision, and it often also needs to support a specific mood or branded look, particularly in areas used for parties or black light sessions. Those are usually separate circuits, not one lighting loop doing both jobs.
Climbing gyms add another layer, because wall mounted spotlighting, auto belay indicator lights and emergency lighting around fall zones all need to keep working independently of each other. A warehouse lighting layout built for storage racking is rarely adequate once the space becomes a venue people actually occupy, and reworking it properly is a job for a qualified electrician rather than a retrofit of existing fittings.
4. RCD protection for a high foot traffic assembly space
AS/NZS 3000 requires additional protection by RCDs with a maximum rated residual current of 30 mA for non domestic final subcircuits feeding socket outlets, lighting, hand held equipment and other circuits that carry an increased risk of electric shock, under Clause 2.6.3.2.3.3. In a venue with constant foot traffic, kids parties, bare feet on trampolines and sweat on every surface, that protection genuinely matters rather than being a box ticking exercise.
In practice this means your switchboard should have several RCDs spread across different circuits, so a single fault or nuisance trip does not take out lighting, point of sale, security and HVAC all at once. A full electrical safety inspection before opening day will confirm every circuit that needs RCD coverage actually has it, rather than relying on whatever protection the previous tenant happened to leave behind.
5. Switchboard capacity planning for a warehouse conversion fitout
Almost every trampoline park or climbing gym we see has moved into a converted warehouse, industrial unit or former big box retail space, and the switchboard in that building was designed for whatever the last tenant did there, not for your venue. Storage and light industrial uses draw a fraction of the power a busy recreation venue needs once you add HVAC, lighting, auto belay systems, EFTPOS, security, a cafe or kitchen, and any charging infrastructure for staff vehicles.
A proper switchboard upgrade starts with a load calculation covering every circuit you plan to install, checked against what your consumer mains can actually deliver. If that supply is already close to its limit, you may also need power supply upgrades from the network before the switchboard work can even begin, which is worth knowing while you are still negotiating lease terms rather than after the fit out has started.
6. Auto belay systems, access control and other safety critical power
Climbing gyms rely on auto belay units that need a continuous, reliable power supply, since a dropout mid climb is a genuine safety issue rather than an inconvenience. These circuits are usually run separately from general power so that a tripped safety switch elsewhere in the building cannot take an active belay device offline.
Access control turnstiles, waiver kiosks, CCTV and alarm systems add further dedicated circuits, and all of this needs to be mapped against your switchboard capacity before equipment suppliers start quoting installation dates. A Level 3 design is often the right starting point for a venue this complex, since it sets out exactly how capacity is allocated across every one of these systems before any cable gets pulled.
Why it's Level 2 ASP work
Any work on the consumer mains, the main switchboard connection or the supply coming in from the street is accredited Level 2 work, not a job a general electrician can sign off. Most warehouse conversions for a trampoline park or climbing gym involve exactly this kind of work, whether that is a single phase to three phase upgrade, a larger consumer mains connection, or a new underground service mains installation feeding a bigger switchboard. A Level 2 electrician in Sydney is the only one authorised to carry out and certify that part of the job.
How High Demand Electrical Helps
We work with a genuine mix of trampoline parks, climbing gyms, and gym and fitness studio electrical fitouts moving into warehouse and industrial spaces across Sydney's West, South West and Sutherland Shire, so we know what a maximum demand calculation for this kind of venue actually needs to cover before the fit out begins. As one of Sydney's most trusted Level 2 ASPs, we handle the consumer mains, switchboard capacity planning and three phase connection in one coordinated scope, rather than leaving you to stitch together separate trades.
We are a licensed local team, not a call centre, and every job starts with a proper site assessment of the existing supply, switchboard and building layout before we quote scope or price. If you already have HVAC, lighting and equipment suppliers lined up, we can work directly from their load figures to confirm your switchboard and consumer mains will actually support them on opening day.
Trampoline Park and Climbing Gym Electrical FAQs (Sydney)
Do I need a three phase upgrade before I fit out a warehouse unit?
Most likely, yes, if the unit currently only has single phase power and you are planning HVAC, lighting and equipment loads typical of a trampoline park or climbing gym. See single phase to three phase upgrades for what that process involves.
Who decides the building classification for my venue?
Your building certifier or council makes the final call based on your specific fit out and intended use, comparing it against the closest National Construction Code classification, which for a large indoor recreation space is commonly an assembly building category similar to an indoor sports centre or stadium.
How many RCDs does a venue like this need?
Enough to spread protection across socket outlets, lighting, kitchen or cafe equipment, and any hand held equipment circuits, rather than one shared unit for the entire switchboard. See electrical safety inspections for how we confirm existing RCD coverage is adequate.
Can the existing switchboard in a warehouse unit cope with a gym or trampoline park fit out?
Rarely without upgrades. The original switchboard was almost always sized for storage or light industrial use, not for the combined HVAC, lighting and safety system load a recreation venue needs. See switchboard upgrades for how capacity is reassessed.
Does my lease affect what electrical work I am responsible for?
It can. Some leases make the tenant responsible for all fit out electrical work including switchboard upgrades, while the landlord retains responsibility for base building supply, so it is worth having a licensed electrician review your proposed loads against the lease before you sign.
Get Your Venue's Power Assessed Before You Sign a Lease
Get a Switchboard Upgrade Quote or Get an Electrical Safety Inspection before you commit to a warehouse unit for your trampoline park or climbing gym. Call 0402 559 777 to talk through your proposed layout. Every job needs a proper site assessment before scope or pricing can be confirmed.
Need Help Fast?
Related Services
Powering Your Needs with Expertise
If you’re looking for a reliable, experienced, and prompt electrician, look no further than High Demand Electrical. We cater to all your electrical needs, from routine maintenance to emergency repairs and complete system installations. Our skilled team is committed to providing professional service that ensures your electrical systems run smoothly. Whether it's a small task or a large project, give us a call today. Let us meet all your electrical demands with the quality and reliability you deserve.




